
Texas summers are hard on electric bills. When the AC runs most of the day from June through September, every bit of wasted electricity adds up. The good news is that some of the best ways to cut your bill and make your home safer are fairly simple electrical upgrades. Here are the ones we recommend most to DFW homeowners, from quick wins to bigger projects.
1. Switch to LED lighting everywhere
This is the easiest win. According to the U.S. Department of Energy, LEDs use at least 75% less energy than incandescent bulbs, last up to 25 times longer, and give off almost no heat. That last part matters in Texas. Old bulbs and halogen fixtures throw off heat that your AC then has to remove.
If you have older recessed cans, we can convert them to sealed LED retrofit trims. That cuts energy use and also seals air leaks into the hot attic above.
2. Install a smart thermostat, correctly
According to ENERGY STAR, heating and cooling make up almost half of the average household’s energy bill. A certified smart thermostat adjusts automatically when you’re away or asleep, and lets you control it from your phone.
The catch is that many smart thermostats need a common wire (C-wire) that older systems don’t have. Without one, they can drain power, act up, or short-cycle your equipment. We make sure the wiring and the system are compatible so it actually saves you money.
3. Add whole-home surge protection
Your AC, furnace control board, water heater, refrigerator, TVs, and computers are all full of electronics that power surges can damage. A whole-home surge protector is installed at your electrical panel and protects every circuit in the house.
It’s important enough that the National Electrical Code now requires a surge protective device whenever a home’s electrical service is installed or replaced. It’s inexpensive insurance compared with replacing an AC control board or a refrigerator.
4. Upgrade an outdated electrical panel
Many older DFW homes still have 100-amp panels, or panel brands with a history of problems. A panel upgrade can make sense if:
- Breakers trip regularly, or your lights dim when the AC kicks on
- You’re adding a heat pump, tankless or heat pump water heater, EV charger, pool, or shop
- The panel is warm, buzzing, rusty, or shows scorch marks
- You’re running out of space for new circuits
An upgraded panel doesn’t lower your bill on its own, but it lets you safely add more efficient equipment, like a heat pump instead of electric resistance heat.
5. Add an EV charger circuit
Charging an electric vehicle on a standard outlet is slow. A properly installed Level 2 charger on a dedicated 240-volt circuit is much faster and lets you charge overnight when your home is using less power. We’ll check your panel capacity first and tell you if a load calculation or service upgrade is needed.
6. Ceiling fans, timers, and smart controls
- Ceiling fans make a room feel noticeably cooler, so you can set the thermostat higher. Just turn them off when nobody’s in the room. Fans cool people, not rooms.
- Timers and smart switches on outdoor lighting, pool pumps, and attic fans stop things from running when they don’t need to.
- Occupancy sensors in garages, laundry rooms, and closets shut lights off automatically.
7. Safety upgrades that go with efficiency
While we’re working in your panel, it’s a good time to bring older homes up to modern safety standards: GFCI protection in kitchens, bathrooms, garages, and outdoors; arc-fault (AFCI) breakers that help prevent electrical fires; and replacement of worn-out outlets, switches, and loose connections that waste power as heat.
One company for HVAC, plumbing, and electrical
Because Brayden J Mechanical is licensed in all three trades, we see how your systems work together. If you’re upgrading to a heat pump, a tankless water heater, or a new HVAC system, we can handle the electrical side too, with no second contractor and no finger-pointing.
We serve Haltom City, Fort Worth, North Richland Hills, Keller, Haslet, Saginaw, Southlake, and the rest of DFW. See our electrical services, schedule a free estimate, or call (682) 277-9944. Texas Electrical Contractor License TECL41866.